Cara mereset printer mp 145 yg full tank / Waste ink tank full. Tidak perlu menggunakan software untuk meresetnya. Biasanya di monitor display keluar kode E 27 atau E 5 untuk mengatasinya adalah sebagai berikut :
1. Cara Reset Printer Canon MP145 dan MP160
- Step 1 : Push Power switch by continue (Tekan Power On/Off)
- Step 2 : insert plug(Masukan Power, Power Tetap di Tekan)
- step 3 : Tekan Tombol Reset 1x, lepaskan Tombol Pwr, Tekan Reset dua kali lagi Sampai Menjadi 0 (tekan tombol tanpa jeda)
- Step 4 : Push + display change from 0 to 1 (tekan tombol + untuk merubah 0 ke 1)
- Step 5 : Push Power switch again , Printer will be print 1 page(tekan tombol power –> tombol start sampai ngeprint 1 hal.)
- step 6 : Open cover (buka tutup printer)
- Step 7 : Unplug (cabut kabel power)
- Step 8 : Take out ink 40 and 41(lepaskan catridge 40 dan 41)
- Step 9 : Insert plug again (pasang kabel power)
- Step 10 : Push power switch (tekan tombol power)
- Step 11 : Open cover (scan cover) (buka tutup scaner)
- Step 12 : Inksert ink 40 , 41 again (masukan catridge 40 dan 41)
2. Berikut ini resep ngereset waste ink counter (error E16 / E27) :
- Matikan printer (kabel power masih tercolok), tekan dan tahan tombol STOP/RESET kemudian tekan tombol ON/OFF
- Tahan tombol ON/OFF, tekan tombol STOP/RESET 2x
- Lepaskan kedua tombol, tunggu sebentar dan printer akan masuk ke SERVICE MODE
- Printer akan charging
- Setelah printer selesai charging, tekan tombol STOP/RESET 4x. (Waste ink counter reset)
- Setiap kali tombol STOP/RESET ditekan, lampu ON/OFF akan berubah warna hijau dan oranye
- Sesudah itu Matikan printer dengan cara menekan tombol ON/OFF ( sebanyak 3 kali agar printer mati total ) dan cabut kabel POWER
- Hidupkan kembali printer.
3. The number of the Reset : button pressing LED Function Remarks 0 time Green Power off
- time Orange Service pattern print
- times Green EEPROM print
- times Orange EEPROM reset
- times Green Waste ink counter reset
- Unplug cable power. (for MP145 / MP150)
- Turn Off Power. (for MP160)
4. Berikut tanda Error Code/Kode Error :
- E2-2 = No paper (ASF)
- E3-3 = Paper jam
- E4 = No ink
- E5-5 = The ink cartridges are not installed or a non-supported ink Cartridge is installed, or the ink cartridges are not installed properly
- E8 = Waste ink absorber full, or platen waste ink absorber full
- E9 = The connected digital camera / video camera does not support Camera Direct Printing
- E14 = The Ink cartridges whose destination are wrong
- E15 = Ink cartridge is not installed E16 – Ink remaining is unknown
- E16 -E19 = Failed to scan head alignment sheet
- E22 = Carriage error
- E23 = Paper feed error
- E24 = Purge unit error
- E25 = ASF(cam) sensor error
- E26 = Internal temperature rise error
- E27 = Waste ink absorber full or platen waste ink absorber full
- E28 = Ink cartridge temperature rise error -
- E29 = EEPROM error
- E33 = Paper feed position error
- E35 15 = USB Host VBUD overcurrent error – USB
- E37 17 = Abnormal motor driver error
- E40 20 = Other hardware error
- E42 22 = Scanner error
Selamat mencoba sobat...